RIVAGE PM Firmware V2.02 (Previous version)

With CL/QL series V4.50 and RIVAGE PM series V2.02, we found that Dante Virtual Soundcard (DVS) V4.0.3.1 or later cannot be recognized as a "SUPPORTED DEVICE" on these consoles. In order to work around this for the time being, we recommend to follow the operation rules below.

Temporary Operations

  • Use earlier versions of DVS than V4.0.3.1.
  • When using V4.0.3.1 or a later version of DVS, mount DVS as an UNSUPPORTED DEVICE, and make the Dante patches from the console or Dante Controller.

Use this file to update RIVAGE PM to V2.02.
Please read the following instructions carefully before updating.

RIVAGE PM Firmware / Editor Compatibility

Please make sure to match all versions of CS-R10, CS-R10-S, CSD-R7, DSP-R10, RPio622, RPio222, and RIVAGE PM Editor when you operate the RIVAGE PM system. Using an unsupported Editor/firmware combination may result in unexpected behavior.
When updating, a TWINLANe network card (HY256-TL, HY256-TL-SMF) must be installed into each rack device in order to update them simultaneously. If any additional TWINLANe network cards are installed after performing the update, please execute the update program again.

Compatibility List

New features in V2.02

  • Added the DSP Mirroring function that allows continuous operation with another DSP engine even if the DSP engine stopped due to a failure.
  • Added the Dual Console function that enables you to connect two control surfaces to one DSP engine.
  • Up to two instances of the RIVAGE PM Editor can be connected to each DSP engine.
  • Now supports remote control via the RIVAGE PM StageMix. Up to two instances of RIVAGE PM StageMix can be connected to each Control Surface/Console.
  • Up to four sets of DSP-R10 or four CSD-R7 can be connected to each I/O Network.
  • Inserting a TWINLANe network card to the HY SLOT2 of the DSP-R10 allows configuration for the SUB I/O Network.
  • Now supports Dante network remote control via the HY144-D card inserted to the HY SLOT3 of DSP-R10 or HY SLOT2 of CSD-R7.
  • Now supports 5.1-channel surround pan/surround monitor.
  • The Mix Minus option is now available for buses.
  • SLOT BRIDGE has been added to the Port to Port function, which enables you to patch sounds across SLOTs.
  • Enabled control of Time Code and Interval in the event list.
  • Added the Preview function.
  • Added the Channel Link function.
  • Added the Channel Move function.
  • Enabled control via the MIDI terminal or the GPI terminal of the DSP engine.
  • Added the Portico5045 effect plug-in.
  • The effect plug-in SEND rack and INSERT rack can be displayed separately.
  • The patch to the effect plug-in mounted on the SEND rack can be operated from the patch grid.
  • Added the CSV File Import/Export functions.
  • The behavior of the channel [ON] key can be switched when using MUTE GROUP.
  • Now supports the Rio3224-D2/Rio1608-D2(V1.10 or later), Rio3224-D/Rio1608-D/Ri8-D/Ro8-D(V4.50 or later).
  • You can remotely control one Rio3224-D2/Rio1608-D2/Rio3224-D/Rio1608-D/Ri8-D/Ro8-D unit from four separate RIVAGE PM10/PM7/CL/QL units.

Improvements in V2.02

  • Improved communication stability of the Console Network.
  • Improved communication stability of the TWINLANe Network.
  • Improved TWINLANe network card recognition at startup.
  • Devices and modules running in incompatible versions can be detected in the FIRMWARE VER screen.
  • Added assignable functions for USER DEFINED KEYS.
  • CUE STACK is now available even if the CUE MODE is set to LAST CUE.
  • Enabled Individual Pan in Stereo channels.
  • Channel name will not be copied when pairing channels.
  • Changed the default setting of the Input to Mix to POST.
  • Changed the default setting of the individual parameters of Recall Safe to ON.
  • Added the PLUG-IN GEQ ALLOCATION setting to the Recall Safe.
  • Changed the default settings of the Oscillator to PINK NOISE, -40dB.
  • Changed the resolution of the Delay knob.

Using RIVAGE PM Editor and RIVAGE PM StageMix simultaneously

When using RIVAGE PM Editor and RIVAGE PM StageMix simultaneously in the same NETWORK connector, set the COMMUNICATION QUALITY to STAGEMIX/EDITOR in the MISC tab of the NETWORK setting on the Control Surface. When selecting the “EDITOR/STAGEMIX” option, which results in greater communication load and slower performance of StageMix, enable IGMP Snooping on the Wi-Fi device.

Fixed Bugs in V2.02

  • Solved a problem in which the “ring connection open!” was displayed with false detection picking up transient state at startup.
  • Solved a problem in which Focus Recall was disabled after updating the same Scene two times.
  • Solved a problem in which the Extracting status may continue to display “Extracting scene data...100%” after finishing SYNC.
  • Solved a problem in which noise occurred at a specific frequency when using the DE-ESSER of the CHANNEL DYNAMICS.
  • Solved some minor errors.

Known issue

  • When a power redundant error occurs in the Rio3224-D2/Rio1608-D2, the SYSTEM/SYNC error message on the RIVAGE PM unit mounted to the Rio3224-D2/Rio1608-D2 is incorrectly displayed as “DANTE SETTING MISMATCH.”

Notices in version updating

  • The project file saving method has been changed from V1.20.
    When loading a project file saved by V1.16 or earlier, the patching of plug-ins may be unintentionally removed. If this happens, manually patch them again.
  • When updating the console’s firmware from V1.20 or earlier, the progress bar may stop at the 14/18 status, or an error may stop the updating process. If this continues for five minutes or longer, turn the power of the console to off and on, and then retry the firmware update.
  • When loading a project file saved by V1.21 and earlier, the RACK Focus status indicator on the SCENE screen may not light even if effect plug-ins or GEQs are the target of Focus Recall. To indicate the Focus status properly, open the SCENE SETUP (FOCUS) pop-up screen once, and then close it. After doing this, save the revised project file to remove this problem in the future.

Notices in version downgrading

  • Do not load a project file saved by V1.51 and later to a system running V1.21 and earlier. When loading, all plug-ins will be un-mounted in all Scenes including the current memory. In this case, re-mounting and setting up of parameters will be required.
  • When downgrading the firmware, be sure to initialize all systems after downgrading.

Notices for usage

  • Even if connecting outputs from two units of DSP-R10 to a port of an I/O Rack via TWINLANe, patches made from other DSP engines will not be displayed on the screen. Be sure not to make duplicate patching. Likewise, the last patch is the priority after device re-booting or TWINLANe re-connection.
  • If you recall a Scene in which a very high HA gain was set, from a scene having a low HA gain, even if no signal is patched, a very loud pink noise signal is occasionally output for a few seconds.
  • When a certain type of USB keyboard is connected to the console, the following message may appear:
    You must restart your computer to apply these changes [Restart Now] [Restart Later]
    If this message is shown, remove this USB keyboard. It is not compatible with the console and cannot be used.
  • When syncing RIVAGE PM Editor or consoles, do not mount any plug-in while the Extracting Scene Data indicator is shown. The mounting information will not be shared, and the settings will be different between them.
  • When a mirroring failover occurs, if the DSP engine B is set to active, the Word Clock master will not change automatically. To prevent sound breakdown, do not turn off the power of the DSP engine A even after a failover occurs.
  • A function for loading Dante device mount information and patch information from the console file will be included in a future version.

VEUILLEZ LIRE ATTENTIVEMENT CE CONTRAT DE LICENCE DE LOGICIEL (« CONTRAT ») AVANT D'UTILISER CE LOGICIEL. VOUS N'ÊTES AUTORISÉ À UTILISER CE LOGICIEL QUE CONFORMÉMENT AUX TERMES ET CONDITIONS DU PRÉSENT ACCORD. CET ACCORD EST CONCLU ENTRE VOUS (EN TANT QUE PERSONNE PHYSIQUE OU MORALE) ET YAMAHA CORPORATION (« YAMAHA »).

EN TELECHARGEANT, EN INSTALLANT, EN COPIANT OU EN UTILISANT DE TOUTE AUTRE MANIERE CE LOGICIEL, VOUS ACCEPTEZ D'ETRE LIE PAR LES TERMES DE CETTE LICENCE. SI VOUS N'ACCEPTEZ PAS LES CONDITIONS, NE TÉLÉCHARGEZ PAS, N'INSTALLEZ PAS, NE COPIEZ PAS ET N'UTILISEZ PAS CE LOGICIEL. SI VOUS AVEZ TÉLÉCHARGÉ OU INSTALLÉ LE LOGICIEL ET QUE VOUS N'ACCEPTEZ PAS LES CONDITIONS, CESSEZ RAPIDEMENT D'UTILISER LE LOGICIEL.

1. OCTROI DE LA LICENCE ET DES DROITS D'AUTEUR

Sous réserve des termes et conditions de cet Accord, Yamaha vous accorde par la présente une licence d'utilisation de copie(s) du/des programme(s) logiciel(s) et des données (« LOGICIEL ») accompagnant cet Accord, uniquement sur un ordinateur, un instrument de musique ou un élément d'équipement que vous possédez ou gérez vous-même. Le terme LOGICIEL englobe toutes les mises à jour du logiciel et des données qui l'accompagnent. Bien que vous soyez propriétaire du support de stockage dans lequel le LOGICIEL est stocké, le LOGICIEL lui-même est la propriété de Yamaha et/ou des concédants de licence de Yamaha, et est protégé par les lois sur les droits d'auteur en vigueur et toutes les dispositions des traités applicables. Bien que vous ayez le droit de revendiquer la propriété des données créées par l'utilisation du logiciel, ce dernier continuera à être protégé par les droits d'auteur pertinents.

2. RESTRICTIONS

  • Il est interdit de procéder à l'ingénierie inverse, au désassemblage, à la décompilation ou à toute autre forme de dérivation du code source du LOGICIEL par quelque méthode que ce soit.
  • Vous ne pouvez pas reproduire, modifier, changer, louer ou distribuer le LOGICIEL en tout ou en partie, ni créer des œuvres dérivées du LOGICIEL.
  • Vous ne pouvez pas transmettre électroniquement le LOGICIEL d'un ordinateur à un autre ou partager le LOGICIEL dans un réseau avec d'autres ordinateurs.
  • Vous ne pouvez pas utiliser le LOGICIEL pour distribuer des données illégales ou des données qui violent l'ordre public.
  • Vous ne pouvez pas lancer de services basés sur l'utilisation du LOGICIEL sans l'autorisation de Yamaha Corporation.
  • Vous ne pouvez pas utiliser le LOGICIEL d'une manière qui pourrait enfreindre les droits d'auteur de tiers ou les droits de propriété de tiers, à moins que vous n'ayez l'autorisation du propriétaire légitime du matériel ou que vous soyez légalement autorisé à l'utiliser.

Les données protégées par le droit d'auteur, y compris, mais sans s'y limiter, les données MIDI pour les chansons, obtenues au moyen du LOGICIEL, sont soumises aux restrictions suivantes que vous devez respecter.

  • Les données reçues au moyen du LOGICIEL ne peuvent être utilisées à des fins commerciales sans l'autorisation du détenteur des droits d'auteur.
  • Les données reçues au moyen du LOGICIEL ne peuvent être dupliquées, transférées ou distribuées, ni lues ou exécutées pour des auditeurs en public sans l'autorisation du détenteur des droits d'auteur.
  • Le cryptage des données reçues au moyen du LOGICIEL ne peut être supprimé et le filigrane électronique ne peut être modifié sans l'autorisation du détenteur des droits d'auteur.

3. TERMINATION

Le présent accord entre en vigueur le jour où vous recevez le LOGICIEL et reste en vigueur jusqu'à ce qu'il soit résilié. En cas de violation d'une loi sur le droit d'auteur ou d'une disposition du présent Accord, celui-ci sera automatiquement et immédiatement résilié sans préavis de la part de Yamaha. En cas de résiliation, vous devez immédiatement cesser d'utiliser le LOGICIEL et détruire tous les documents écrits qui l'accompagnent ainsi que toutes les copies de ces documents.

4. EXCLUSION DE GARANTIE SUR LES LOGICIELS

Si vous pensez que le processus de téléchargement était défectueux, vous pouvez contacter Yamaha, et Yamaha vous permettra de télécharger à nouveau le LOGICIEL, à condition que vous détruisiez d'abord toutes les copies ou copies partielles du LOGICIEL que vous avez obtenues lors de votre précédente tentative de téléchargement. Cette autorisation de retéléchargement ne limite en rien l'exclusion de garantie prévue à l'article 5 ci-dessous.
Vous reconnaissez et acceptez expressément que l'utilisation du LOGICIEL se fait à vos risques et périls. Le LOGICIEL et la documentation y afférente sont fournis « en l'état » et sans garantie d'aucune sorte. NONOBSTANT TOUTE AUTRE DISPOSITION DE CET ACCORD, YAMAHA REJETTE EXPRESSÉMENT TOUTES LES GARANTIES RELATIVES AU LOGICIEL, QU'ELLES SOIENT EXPRESSES OU IMPLICITES, Y COMPRIS, MAIS SANS S'Y LIMITER, LES GARANTIES IMPLICITES DE QUALITÉ MARCHANDE, D'ADÉQUATION À UN USAGE PARTICULIER ET DE NON-VIOLATION DES DROITS DES TIERS. EN PARTICULIER, MAIS SANS LIMITER CE QUI PRÉCÈDE, YAMAHA NE GARANTIT PAS QUE LE LOGICIEL RÉPONDRA À VOS EXIGENCES, QUE LE FONCTIONNEMENT DU LOGICIEL SERA ININTERROMPU OU SANS ERREUR, OU QUE LES DÉFAUTS DU LOGICIEL SERONT CORRIGÉS.

5. LIMITATION DE LA RESPONSABILITÉ

L'OBLIGATION ENTIÈRE DE YAMAHA EN VERTU DES PRÉSENTES SERA DE PERMETTRE L'UTILISATION DU LOGICIEL SELON LES TERMES DES PRÉSENTES. EN AUCUN CAS YAMAHA NE SERA RESPONSABLE ENVERS VOUS OU TOUTE AUTRE PERSONNE DE TOUT DOMMAGE, Y COMPRIS, SANS S'Y LIMITER, TOUT DOMMAGE DIRECT, INDIRECT, ACCESSOIRE OU CONSÉCUTIF, TOUTE DÉPENSE, TOUT MANQUE À GAGNER, TOUTE PERTE DE DONNÉES OU TOUT AUTRE DOMMAGE RÉSULTANT DE L'UTILISATION, DE LA MAUVAISE UTILISATION OU DE L'INCAPACITÉ À UTILISER LE LOGICIEL, MÊME SI YAMAHA OU UN REVENDEUR AGRÉÉ A ÉTÉ AVERTI DE LA POSSIBILITÉ DE TELS DOMMAGES. En aucun cas la responsabilité totale de Yamaha envers vous pour tous les dommages, pertes et causes d'action (qu'ils soient contractuels, délictuels ou autres) ne dépassera le montant payé pour le LOGICIEL.

6. LOGICIEL LIBRE

Ce LOGICIEL peut inclure le logiciel ou ses modifications qui incluent des licences open source, y compris, mais sans s'y limiter, la GNU General Public License ou la Lesser General Public License (« LOGICIEL OPEN SOURCE »). Votre utilisation des logiciels libres est soumise aux conditions de licence spécifiées par chaque détenteur de droits. En cas de conflit entre les termes et conditions du présent accord et chaque licence de source ouverte, les termes de la licence de source ouverte prévaudront uniquement en cas de conflit.

7. LOGICIELS ET SERVICES DE TIERS

Des logiciels, services et données de tiers (« LOGICIELS DE TIERS ») peuvent être attachés au LOGICIEL. SI, dans les documents écrits ou les données électroniques accompagnant le logiciel, Yamaha identifie tout logiciel et toute donnée en tant que LOGICIEL TIERS, vous reconnaissez et acceptez que vous devez respecter les conditions de tout accord fourni avec le LOGICIEL TIERS et que la partie fournissant le LOGICIEL TIERS est responsable de toute garantie ou responsabilité liée à ou découlant du LOGICIEL TIERS. Yamaha n'est en aucun cas responsable du LOGICIEL TIERS ou de l'utilisation que vous en faites.

  • Yamaha ne fournit aucune garantie expresse quant au LOGICIEL TIERS. EN OUTRE, YAMAHA DÉCLINE EXPRESSÉMENT TOUTE GARANTIE IMPLICITE, Y COMPRIS, MAIS SANS S'Y LIMITER, LES GARANTIES IMPLICITES DE QUALITÉ MARCHANDE ET D'ADÉQUATION À UN USAGE PARTICULIER, CONCERNANT LE LOGICIEL TIERS.
  • Yamaha ne vous fournira aucun service ou entretien concernant le LOGICIEL TIERS.

Yamaha n'est pas responsable envers vous ou toute autre personne de tout dommage, y compris, sans limitation, tout dommage direct, indirect, accessoire ou consécutif, dépenses, perte de profits, perte de données ou autres dommages résultant de l'utilisation, de la mauvaise utilisation ou de l'incapacité d'utiliser le LOGICIEL TIERS.

AVIS DE RESTRICTION DES DROITS DU GOUVERNEMENT DES ÉTATS-UNIS :
Le logiciel est un « article commercial », tel que ce terme est défini dans le 48 C.F.R. 2.101 (oct. 1995), consistant en un « logiciel informatique commercial » et une « documentation de logiciel informatique commercial », tels que ces termes sont utilisés dans le 48 C.F.R. 12.212 (sept. 1995). Conformément à 48 C.F.R. 12.212 et 48 C.F.R. 227.7202-1 à 227.72024 (juin 1995), tous les utilisateurs finaux du gouvernement des États-Unis doivent acquérir le logiciel avec les seuls droits énoncés dans le présent document.

8. GÉNÉRALITÉS

Le présent accord est interprété et régi par le droit japonais, sans référence aux principes de conflit de lois. Tout litige ou procédure est porté devant le tribunal de district de Tokyo au Japon. Si, pour quelque raison que ce soit, un tribunal compétent estime qu'une partie du présent accord est inapplicable, le reste de l'accord reste pleinement en vigueur. Tous les avis juridiques, les avis de litiges et les demandes d'arbitrage, ainsi que tout autre avis visant à modifier les présentes dispositions ou à faire valoir des droits légaux doivent être envoyés par écrit à l'adresse suivante :

Yamaha Corporation
10-1, Nakazawa-cho, Chuo-ku, Hamamatsu, Shizuoka, 430-8650, Japan

9. INTÉGRALITÉ DE L'ACCORD

Le présent accord constitue l'intégralité de l'accord entre les parties en ce qui concerne l'utilisation du LOGICIEL et de tous les documents écrits qui l'accompagnent et remplace tous les accords ou conventions antérieurs ou contemporains, écrits ou oraux, concernant l'objet du présent accord.

10. AMENDEMENT

Yamaha peut modifier, réviser ou mettre à jour cet Accord à sa discrétion. Toute modification ou mise à jour que Yamaha apporte à cet Accord sera effective après que vous ayez accepté les conditions mises à jour de cet Accord ou utilisé ce LOGICIEL.

Last updated : November 1, 2024