QL1 Firmware V4.10-2 (Previous version)
Important Notices
Dante firmware has been changed to "3.10.32.2-4.0.35.1-1.3.4". This change corresponds to the hardware change of the Dante module due to the completion of part production. The function is the same as the previous version "3.10.0.19-4.0.3.1-1.3.2", and there is no change in the product firmware. Therefore, customers already using V4.10 do not need updating. In addition, Dante firmware "3.10.0.19-4.0.3.1-1.3.2" and "3.10.32.2-4.0.35.1-1.3.4" products can be used together. Please refer to the version compatibility table of each device.
With CL/QL series firmware V4.10, we found a problem which causes an error message and requires a console restart, after changing the Dante network configuration under specific conditions. To avoid this, we strongly recommend following the operation rules below until new firmware is released to fix this bug.
Symptoms
The "Network Audio Module Failed. Please Restart the Console." error message appears, and the Dante settings fail to work anymore until the console is restarted.
Temporary Operation Rules
- Follow the rules below if the CL/QL series' Secondary Port is set to Redundant (The issues do not occur with Daisy-Chain).
- Restart the CL/QL consoles once the Dante settings of the mounted devices such as R series I/O racks have been changed (for example from DAISY CHAIN to REDUNDANT).
- Restart the CL/QL consoles once the Fs of the mounted devices such as RSio64-D has been changed which increased/decreased the number of channels.
- Do not mount Dante Via (Unsupported Device) on CL/QL. Use Dante Controller to make the patch if needed.
- Even if the error message should appear, that would not stop audio. Restart the console after waiting for an appropriate time.
The audio signal sent to MATRIX 7/8 is momentarily output at unity gain when the channel is muted by a DCA group and the ON/CUE keys are operated.
This momentary audio-leak occurs in either of two conditions:
- When enabling the DCA mute for input channels or MIX buses that are sending to MATRIX 7/8.
- When operating the channel ON key or CUE key while DCA mute is applied for an input channel or MIX bus that is sending to MATRIX 7/8.
This issue can be prevented in advance by following this procedure:
- Enable "USE MATRIX 7/8 AS CUE B" on the CUE setting page to enable CUE B.
- Set CUE B's listening positions both for INPUT and OUTPUT to AFL .
- Press "USE MATRIX 7/8 AS CUE B" again to disable CUE B .
Use this file to update QL to V4.10. Please read the following instructions before updating.
Caution when updating
- Use the "ql*_firm410-2.zip" (* is the model number) when updating.
- Copy files "MQLP4_10.PGM" to the root directory of the USB memory. Follow the instructions on the update guide.
- You also need to update the Dante firmware. You can now update the Dante firmware for CL also by using the USB memory. This method allows you to update both the firmware and the "MQLP4_10.PGM" files together at the same time.
- If the message "NAME SUB CPU is old" appears after updating to V4.10, copy "QL-MD103.BIN" file in QL*_firm410/NAME SUB (* is the model number) to the root directory of the USB memory. Follow the instructions on the update guide. This method allows you to update both the Dante firmware and the "MQLP4_10.PGM" files together at the same time.
*IMPORTANT NOTE*
- Before copying files, delete all files with extension .PGM and .BIN if any exists in the root directory of the USB memory. Prior to V3.0, the CL and QL Series used different files when updating, but both files used the same name * "C-MD1.BIN." For this reason, an error may occur during update when the incorrect "C-MD1.BIN" file is used or left in the root directory.
- Updating Dante firmware by using a USB memory takes approximately10 minutes.
Please do not use the EEE function (*) of network switches in a Dante network.
Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts.
Therefore we strongly recommend that:- - If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic.
- - If you use unmanaged switches, make sure to not use network switches that support EEE
- * EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.
Cautions for Dante Firmware
- You need to update the Dante-MY16-AUD firmware to V3.3.9 or later before using the Dante-MY16-AUD with the CL series.
- The Dante Firmware Update Manager since v1.4.16.6 for Windows does not support Windows XP. Please use Windows 7, Windows 8/8.1, or Windows 10.
CL/QL/RIVAGE/R/Tio Series Editor/Firmware/R Remote Compatibility
Please make sure to use appropriate version of CL Editor or QL Editor which is compatible with your console firmware in reference to the following compatibility chart. Using an unsupported Editor/firmware combination may result in unexpected behavior.
The Firmware Set is a set of main (and sub) firmware of the device and the Dante firmware. The version of Firmware Set is the same as the version of the main firmware. Refer to the release note of each firmware about the details of the Firmware Set.
Main Revisions and Enhancements
- You can use the following amount of CL/QL/R Remote units to remotely control each device unit (listed at left).
RSio64-D/Tio1608-D: Maximum of two CL/QL/R Remote unitsRMio64-D: Maximum of six CL/QL/R Remote unitsRio/Ri/Ro: Maximum of four CL/QL units plus two separate computers operating R Remote.
- You can connect maximum of ten iOS devices operating MonitorMix.
New features in V4.10
- Now supports the AES67 standard for audio-over-IP interoperability.
- Now supports the "Dante Device Lock" function.
- You can now control the Shure ATX400, QLXD4 and ULXD4 devices, which do not support Dante.
- You can now set “DHCP” and “STATIC IP” for the use of remote control.
Make sure to assign the IP address for device control to a different subnet from that for mixer control. If both addresses are set to the same subnet, the device control and the mixer control will not work.
- Now supports Audinate Dante-MY16-AUD2 and d&b audiotechnik DS10.
Assign the following device labels by Dante Controller to detect as a SUPPORTED DEVICE.
Y###-********** # is a UNIT ID, a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A - F (000 - FFF)
* indicates any desired character (alphabetical uppercase or lowercase, numerals, or -(hyphen) may be used) - You can now set an EQ type to entire channels at once.
- Added a function to display the status of the internal Sampling Rate Converter in MY8-AE96S MY card inserted into the RSio64-D.
Improvements in V4.10
- Color name is also shown on the Channel Color Select buttons.
- When the Dante network does not link as Gigabit Ethernet, a message will appear on the lower part of the LCD.
- The selection of EQ band is now linked between the panel and the touch screen.
- In the RTA screen, visibility of frequency analysis has been improved by adding the “Changing the scale” parameter and the “Gain offset” parameter.
- The channel name and the effect type are now displayed on the PATCH/NAME popup window, the CH SELECT popup window and the PORT SELECT popup window.
- You can now switch the EQ type of the PRECISE type EQ to “Shelving-type” or “Filter” by pressing and turning the Q knob.
- The range of the fader calibration is now extended on the point of 0db.
Fixed bugs in V4.10
- Solved a problem in which, when a RSio64-D is not mounted, loading a console file (for which the RSio64-D had previously been mounted) would initialize the user patch settings, since the console could not retrieve the device settings correctly.
- Solved a problem in which defeating a 31-band GEQ LINK setting would also defeat the link setting on adjacent racks.
Known issue
- If Dante Virtual Soundcard (DVS) is patched to the QL series device using Dante Controller, the patching may not be recalled correctly when the QL series device is restarted. In such cases, patch the DVS again. In addition, when using a version of DVS for Windows that is older than v3.2.0, patches after CH41 cannot be performed from QL series consoles.
- Loading of a file created by version V1.15 or older will not include the mount information of Dante devices other than any connected R-series. It is the same when recalling a DANTE INPUT PATCH LIBRARY. Please reset MOUNT, PATCH, and DANTE INPUT PATCH Library data using V1.51 or later if necessary.
NOTICE
- When setting up the latency in Dante Controller, and there is a discrepancy in latency with the transmit device or the receive device, the largest (slowest) latency setting becomes effective.
- The following device labels are used for detecting a SUPPORTED DEVICE. (except Dante non-supported devices)
Y###-**********# is a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A - F (000 - FFF)*indicates any desired character (alphabetical uppercase or lowercase, numerals, or -(hyphen) may be used)Up to 31 characters including the 'Y' are supported.For the R-series, make sure that the ID indicated by Y###- is not duplicated by any other R-series unit, even if it is a different size.
- In V2.0 and later, custom fader bank settings are not only included in user settings, but in scene data as well. The custom fader bank settings that are called up vary depending on the logged-in user, the type of the loaded data, and the version. Please note the following points:
If you load console data of the ALL type as Administrator, the custom fader bank settings for the saved Administrator are recalled. If you load ALL data as Guest or another user, the custom fader bank settings for the saved current scene are called up.If you load ALL data that was saved in CL V1.70 or earlier, since scenes do not include custom fader bank settings, the custom fader bank settings for the current scene when the load was performed are applied to all scenes. Therefore, before loading ALL data, we recommend that you either change users to set the custom fader bank to the desired setting, or that you enable Recall Safe for the custom fader bank.
- File Converter V5.0.0, compatible with CL firmware V2.xx, V3.xx, V4.xx and V5.xx and QL firmware V3.xx, V4.xx and V5.xx has been made available for use.
Accord de licence et fichier de téléchargement
VEUILLEZ LIRE ATTENTIVEMENT CE CONTRAT DE LICENCE DE LOGICIEL (« CONTRAT ») AVANT D'UTILISER CE LOGICIEL. VOUS N'ÊTES AUTORISÉ À UTILISER CE LOGICIEL QUE CONFORMÉMENT AUX TERMES ET CONDITIONS DU PRÉSENT ACCORD. CET ACCORD EST CONCLU ENTRE VOUS (EN TANT QUE PERSONNE PHYSIQUE OU MORALE) ET YAMAHA CORPORATION (« YAMAHA »).
EN TELECHARGEANT, EN INSTALLANT, EN COPIANT OU EN UTILISANT DE TOUTE AUTRE MANIERE CE LOGICIEL, VOUS ACCEPTEZ D'ETRE LIE PAR LES TERMES DE CETTE LICENCE. SI VOUS N'ACCEPTEZ PAS LES CONDITIONS, NE TÉLÉCHARGEZ PAS, N'INSTALLEZ PAS, NE COPIEZ PAS ET N'UTILISEZ PAS CE LOGICIEL. SI VOUS AVEZ TÉLÉCHARGÉ OU INSTALLÉ LE LOGICIEL ET QUE VOUS N'ACCEPTEZ PAS LES CONDITIONS, CESSEZ RAPIDEMENT D'UTILISER LE LOGICIEL.
1. OCTROI DE LA LICENCE ET DES DROITS D'AUTEUR
Sous réserve des termes et conditions de cet Accord, Yamaha vous accorde par la présente une licence d'utilisation de copie(s) du/des programme(s) logiciel(s) et des données (« LOGICIEL ») accompagnant cet Accord, uniquement sur un ordinateur, un instrument de musique ou un élément d'équipement que vous possédez ou gérez vous-même. Le terme LOGICIEL englobe toutes les mises à jour du logiciel et des données qui l'accompagnent. Bien que vous soyez propriétaire du support de stockage dans lequel le LOGICIEL est stocké, le LOGICIEL lui-même est la propriété de Yamaha et/ou des concédants de licence de Yamaha, et est protégé par les lois sur les droits d'auteur en vigueur et toutes les dispositions des traités applicables. Bien que vous ayez le droit de revendiquer la propriété des données créées par l'utilisation du logiciel, ce dernier continuera à être protégé par les droits d'auteur pertinents.
2. RESTRICTIONS
- Il est interdit de procéder à l'ingénierie inverse, au désassemblage, à la décompilation ou à toute autre forme de dérivation du code source du LOGICIEL par quelque méthode que ce soit.
- Vous ne pouvez pas reproduire, modifier, changer, louer ou distribuer le LOGICIEL en tout ou en partie, ni créer des œuvres dérivées du LOGICIEL.
- Vous ne pouvez pas transmettre électroniquement le LOGICIEL d'un ordinateur à un autre ou partager le LOGICIEL dans un réseau avec d'autres ordinateurs.
- Vous ne pouvez pas utiliser le LOGICIEL pour distribuer des données illégales ou des données qui violent l'ordre public.
- Vous ne pouvez pas lancer de services basés sur l'utilisation du LOGICIEL sans l'autorisation de Yamaha Corporation.
- Vous ne pouvez pas utiliser le LOGICIEL d'une manière qui pourrait enfreindre les droits d'auteur de tiers ou les droits de propriété de tiers, à moins que vous n'ayez l'autorisation du propriétaire légitime du matériel ou que vous soyez légalement autorisé à l'utiliser.
Les données protégées par le droit d'auteur, y compris, mais sans s'y limiter, les données MIDI pour les chansons, obtenues au moyen du LOGICIEL, sont soumises aux restrictions suivantes que vous devez respecter.
- Les données reçues au moyen du LOGICIEL ne peuvent être utilisées à des fins commerciales sans l'autorisation du détenteur des droits d'auteur.
- Les données reçues au moyen du LOGICIEL ne peuvent être dupliquées, transférées ou distribuées, ni lues ou exécutées pour des auditeurs en public sans l'autorisation du détenteur des droits d'auteur.
- Le cryptage des données reçues au moyen du LOGICIEL ne peut être supprimé et le filigrane électronique ne peut être modifié sans l'autorisation du détenteur des droits d'auteur.
3. TERMINATION
Le présent accord entre en vigueur le jour où vous recevez le LOGICIEL et reste en vigueur jusqu'à ce qu'il soit résilié. En cas de violation d'une loi sur le droit d'auteur ou d'une disposition du présent Accord, celui-ci sera automatiquement et immédiatement résilié sans préavis de la part de Yamaha. En cas de résiliation, vous devez immédiatement cesser d'utiliser le LOGICIEL et détruire tous les documents écrits qui l'accompagnent ainsi que toutes les copies de ces documents.
4. EXCLUSION DE GARANTIE SUR LES LOGICIELS
Si vous pensez que le processus de téléchargement était défectueux, vous pouvez contacter Yamaha, et Yamaha vous permettra de télécharger à nouveau le LOGICIEL, à condition que vous détruisiez d'abord toutes les copies ou copies partielles du LOGICIEL que vous avez obtenues lors de votre précédente tentative de téléchargement. Cette autorisation de retéléchargement ne limite en rien l'exclusion de garantie prévue à l'article 5 ci-dessous.
Vous reconnaissez et acceptez expressément que l'utilisation du LOGICIEL se fait à vos risques et périls. Le LOGICIEL et la documentation y afférente sont fournis « en l'état » et sans garantie d'aucune sorte. NONOBSTANT TOUTE AUTRE DISPOSITION DE CET ACCORD, YAMAHA REJETTE EXPRESSÉMENT TOUTES LES GARANTIES RELATIVES AU LOGICIEL, QU'ELLES SOIENT EXPRESSES OU IMPLICITES, Y COMPRIS, MAIS SANS S'Y LIMITER, LES GARANTIES IMPLICITES DE QUALITÉ MARCHANDE, D'ADÉQUATION À UN USAGE PARTICULIER ET DE NON-VIOLATION DES DROITS DES TIERS. EN PARTICULIER, MAIS SANS LIMITER CE QUI PRÉCÈDE, YAMAHA NE GARANTIT PAS QUE LE LOGICIEL RÉPONDRA À VOS EXIGENCES, QUE LE FONCTIONNEMENT DU LOGICIEL SERA ININTERROMPU OU SANS ERREUR, OU QUE LES DÉFAUTS DU LOGICIEL SERONT CORRIGÉS.
5. LIMITATION DE LA RESPONSABILITÉ
L'OBLIGATION ENTIÈRE DE YAMAHA EN VERTU DES PRÉSENTES SERA DE PERMETTRE L'UTILISATION DU LOGICIEL SELON LES TERMES DES PRÉSENTES. EN AUCUN CAS YAMAHA NE SERA RESPONSABLE ENVERS VOUS OU TOUTE AUTRE PERSONNE DE TOUT DOMMAGE, Y COMPRIS, SANS S'Y LIMITER, TOUT DOMMAGE DIRECT, INDIRECT, ACCESSOIRE OU CONSÉCUTIF, TOUTE DÉPENSE, TOUT MANQUE À GAGNER, TOUTE PERTE DE DONNÉES OU TOUT AUTRE DOMMAGE RÉSULTANT DE L'UTILISATION, DE LA MAUVAISE UTILISATION OU DE L'INCAPACITÉ À UTILISER LE LOGICIEL, MÊME SI YAMAHA OU UN REVENDEUR AGRÉÉ A ÉTÉ AVERTI DE LA POSSIBILITÉ DE TELS DOMMAGES. En aucun cas la responsabilité totale de Yamaha envers vous pour tous les dommages, pertes et causes d'action (qu'ils soient contractuels, délictuels ou autres) ne dépassera le montant payé pour le LOGICIEL.
6. LOGICIEL LIBRE
Ce LOGICIEL peut inclure le logiciel ou ses modifications qui incluent des licences open source, y compris, mais sans s'y limiter, la GNU General Public License ou la Lesser General Public License (« LOGICIEL OPEN SOURCE »). Votre utilisation des logiciels libres est soumise aux conditions de licence spécifiées par chaque détenteur de droits. En cas de conflit entre les termes et conditions du présent accord et chaque licence de source ouverte, les termes de la licence de source ouverte prévaudront uniquement en cas de conflit.
7. LOGICIELS ET SERVICES DE TIERS
Des logiciels, services et données de tiers (« LOGICIELS DE TIERS ») peuvent être attachés au LOGICIEL. SI, dans les documents écrits ou les données électroniques accompagnant le logiciel, Yamaha identifie tout logiciel et toute donnée en tant que LOGICIEL TIERS, vous reconnaissez et acceptez que vous devez respecter les conditions de tout accord fourni avec le LOGICIEL TIERS et que la partie fournissant le LOGICIEL TIERS est responsable de toute garantie ou responsabilité liée à ou découlant du LOGICIEL TIERS. Yamaha n'est en aucun cas responsable du LOGICIEL TIERS ou de l'utilisation que vous en faites.
- Yamaha ne fournit aucune garantie expresse quant au LOGICIEL TIERS. EN OUTRE, YAMAHA DÉCLINE EXPRESSÉMENT TOUTE GARANTIE IMPLICITE, Y COMPRIS, MAIS SANS S'Y LIMITER, LES GARANTIES IMPLICITES DE QUALITÉ MARCHANDE ET D'ADÉQUATION À UN USAGE PARTICULIER, CONCERNANT LE LOGICIEL TIERS.
- Yamaha ne vous fournira aucun service ou entretien concernant le LOGICIEL TIERS.
Yamaha n'est pas responsable envers vous ou toute autre personne de tout dommage, y compris, sans limitation, tout dommage direct, indirect, accessoire ou consécutif, dépenses, perte de profits, perte de données ou autres dommages résultant de l'utilisation, de la mauvaise utilisation ou de l'incapacité d'utiliser le LOGICIEL TIERS.
AVIS DE RESTRICTION DES DROITS DU GOUVERNEMENT DES ÉTATS-UNIS :
Le logiciel est un « article commercial », tel que ce terme est défini dans le 48 C.F.R. 2.101 (oct. 1995), consistant en un « logiciel informatique commercial » et une « documentation de logiciel informatique commercial », tels que ces termes sont utilisés dans le 48 C.F.R. 12.212 (sept. 1995). Conformément à 48 C.F.R. 12.212 et 48 C.F.R. 227.7202-1 à 227.72024 (juin 1995), tous les utilisateurs finaux du gouvernement des États-Unis doivent acquérir le logiciel avec les seuls droits énoncés dans le présent document.
8. GÉNÉRALITÉS
Le présent accord est interprété et régi par le droit japonais, sans référence aux principes de conflit de lois. Tout litige ou procédure est porté devant le tribunal de district de Tokyo au Japon. Si, pour quelque raison que ce soit, un tribunal compétent estime qu'une partie du présent accord est inapplicable, le reste de l'accord reste pleinement en vigueur. Tous les avis juridiques, les avis de litiges et les demandes d'arbitrage, ainsi que tout autre avis visant à modifier les présentes dispositions ou à faire valoir des droits légaux doivent être envoyés par écrit à l'adresse suivante :
Yamaha Corporation
10-1, Nakazawa-cho, Chuo-ku, Hamamatsu, Shizuoka, 430-8650, Japan
9. INTÉGRALITÉ DE L'ACCORD
Le présent accord constitue l'intégralité de l'accord entre les parties en ce qui concerne l'utilisation du LOGICIEL et de tous les documents écrits qui l'accompagnent et remplace tous les accords ou conventions antérieurs ou contemporains, écrits ou oraux, concernant l'objet du présent accord.
10. AMENDEMENT
Yamaha peut modifier, réviser ou mettre à jour cet Accord à sa discrétion. Toute modification ou mise à jour que Yamaha apporte à cet Accord sera effective après que vous ayez accepté les conditions mises à jour de cet Accord ou utilisé ce LOGICIEL.
Last updated : November 1, 2024
Tu as aussi besoin
Manuels d'installation
Versions précédentes
QL1 Firmware
- Previous versions information
- QL1 Firmware V5.85
- QL1 Firmware V5.81
- QL1 Firmware V5.80
- QL1 Firmware V5.70
- QL1 Firmware V5.60
- QL1 Firmware V5.51
- QL1 Firmware V5.50
- QL1 Firmware V5.10
- QL1 Firmware V5.01
- QL1 Firmware V5.00
- QL1 Firmware V4.51
- QL1 Firmware V4.50
- QL1 Firmware V4.10-2
- QL1 Firmware V4.04-2
- QL1 Firmware V4.02
- QL1 Firmware V4.01
- QL1 Firmware V4.00
- QL1 Firmware V3.11-2
- QL1 Firmware V3.10
- QL1 Firmware V3.02
- QL1 Firmware V1.08
- QL1 Firmware V1.07
- QL1 Firmware V1.02-2