MONTAGE OS Updater V3.51

This update is applicable to the following models:

MONTAGE6 / MONTAGE6 WH / MONTAGE7 / MONTAGE7 WH / MONTAGE8 / MONTAGE8 WH with firmware versions earlier than V3.51

  1. Press the [UTILITY] button to open the Utility display.
  2. Touch [Setting] tab to [System] tab at the left side of the display.
  3. The following message appears in the bottom of the display:

MONTAGE Firmware Version: *.**.*(c)2016 Yamaha Corporation

The unit's version is indicated by " MONTAGE Firmware Version: *.**.* "

Only the numbers up to the two decimal places after the first dot are important in reading the version number, you can ignore the numbers after the second dot.
Ex.) 1.02.0 =1.02 , 1.10.0= 1.10

  • One USB flash drive of over 1GB capacity formatted on the MONTAGE

Fixes and Enhancemenets

V3.50 to V3.51

Fixed problems;

  • Fixed a problem in which the Pitch Bend controller could not control any parameters.
  • Fixed a problem in which the Live Set information in a MODX User file might not be loaded properly, with the result that the link destination Performance of each slot might be set to "Init Normal (AWM2)."

V3.00 to V3.50

New features;

  • New Performances have been added.
  • The Smart Morph function has been added.
  • New functions have been added to the Pattern Sequencer.
  • MODX files can now be imported.
  • Controllability and playability have been improved.

V2.50 to V3.00

New features;

  • New effect types have been added.
  • New Performances have been added.
  • The Pattern Sequencer function has been added.
  • The Rhythm Pattern function has been added.
  • You can now play songs, patterns and audio files from the Live Set display.
  • Super Knob Link has been added to the data that is recorded in the Scene function.
  • Keyboard Control has been added to the data that is recorded in the Scene function.
  • Increased the range of the LFO Speed parameter.
  • You can now connect MIDI equipment via the USB TO DEVICE terminal.
  • The Global Micro Tuning settings have been added.
  • The Audition Loop setting has been added.
  • Improvements have been made to the user interface.
  • The Note capacity (total area in Store) has been increased from 130,000 to 520,000 (for Songs) and 520,000 (for Patterns).

Fixed problems;

  • Fixed other minor problems.

V2.00 to V2.50

New features;

  • New Performances have been added.
  • The DAW Remote function has been added.
  • A new function has been added that allows you to selectively enable (or disable) recording of Arpeggio data, when recording MIDI songs.
  • You can now set a Center note in the Edit Waveform display.
  • You can now set a key for assignment when loading WAV files or AIFF files as waveforms.
  • You can now select the Assignable Knob for Common Parts, by pressing the [PART COMMON] in the dialog displayed when selecting the Part parameter and pressing the [CONTROL ASSIGN] button.
  • The Panel Lock function has been added to prevent inadvertent operations during your performance.

Fixed problems;

  • Fixed a problem in which the footswitch would freeze when it's used as a sostenuto in combination with the sustain pedal.
  • Fixed other minor problems.

V1.60 to V2.00

New features;

  • New Performances have been added.
  • You can now create User Audition Phrases.
  • New functions have been added in some displays for simplifying Super Knob settings.
  • Transitioning of displays during edits have been improved.
  • You can now set the Live Set slot as a startup display.
  • You can now apply the Live Set Font Size to the Category Names in the Category Search display.
  • You can now load MOXF files.
  • You can now load Performance data for the MOTIF XS, MOTIF XF, and MOXF.
  • You can now set to keep the current tempo after switching to a different Performance.
  • You can now set to keep the current A/D Part volume after switching to a different Performance.
  • The shortcuts for opening the Control Assign display have been added in the Envelope Follower display.
  • You can now select the Super Knob, Motion Sequencer Lane, or Envelope Follower as a source in the dialog that appears when the [CONTROL ASSIGN] button is pressed.
  • New function that emphasize the connected lines in the Overview display to indicate the controller you are operating and its destinations has been added.
  • Increased the number of Songs that can be recorded in the MIDI tab of the Play/Rec display from 64 to 128.
  • The shortcuts for opening the Tempo Settings display have been added in the Play/Rec display.
  • The selected slot will remain active even after you changed to other banks in Live Set display.

Fixed problems;

  • Fixed other minor problems.

V1.51 to V1.60

New features;

  • New effect types have been added.
  • New Performances have been added.
  • New functions have been added in some displays for simplifying Super Knob settings.
  • Improved the Keyboard Velocity Curve on MONTAGE6/MONTAGE7.

Fixed problems;

  • Fixed a problem in which playback would continue without stopping if you switched a Performance with received Sustain messages from external equipment in the MIDI single channel mode.
  • Fixed other minor problems.

V1.50 to V1.51

Fixed problems;

  • Fixed a problem in which this instrument would freeze if you move from the Element view to the Edit display while the cursor is left on the Element view.
  • Fixed a problem in which the desired Part would not be properly displayed after you switch Parts while the Element view is displayed.
  • Fixed other minor problems.

V1.20 to V1.50

New features;

  • New effect types have been added.
  • New Performances have been added.
  • The Favorite function has been added.
  • "Mixing" has been added for the "Parameter with Part" setting of the Part Category Search.
  • From the Performance Play (Home) display, you can now see various information.
  • The Super Knob Link function has been added.
  • You can now control the monitor volume of the Audio signal input from the [USB TO HOST] terminal.
  • You can now switch Scenes by Control Change messages.
  • You can now make partial changes to the font size on the Live Set display and the Category Search display.
  • You can now save/load backup files in which the entire User Memory data (including Songs and Libraries) is stored.
  • Each Edit display has been improved by allowing touch selection of Parts from the display.
  • Improved the sensitivity of Audio Beat Sync.
  • Improved the visibility of the selected Performance in the Live Set display.
  • MOXF6/MOXF8 data (X6A, X6V, X6G, and X6W) can now be loaded to MONTAGE.
  • Enhanced the Note Shift control from the panel (holding down the [SHIFT] button and using the OCTAVE [-]/[+] buttons to change the transpose value in semitones), so that once you change the value, you can release your finger from the [SHIFT] button and continue to make semitone changes for a short time by using only the OCTAVE [-]/[+] buttons.

Fixed problems;

  • Fixed a problem in which an error message would appear when Device Number was set to other than "All" and a Super Knob Control Change message was received.
  • Fixed a problem in which Zone settings would not be correctly applied by switching Performances.
  • Fixed other minor problems.

V1.11 to V1.20

New features;

  • Switching time between Performances has been reduced.
  • Element / Operator Control has been added for "Control Function."
  • You can now store Control Function settings as Performance data.
  • Song Loop playback function has been added.
  • User Arpeggio function has been added.
  • You can now separately mute original Parts and newly added Parts by Performance Merge.
  • Monitor Volume settings for USB connection have been added.
  • You can now control the Super Knob by MIDI Control Change messages.
  • You can now copy or exchange Arpeggio Types.
  • You can now copy or exchange Motion Sequences.
  • You can now copy or exchange between Live Sets in different Banks on a page basis.
  • The MONTAGE Connect computer application is now supported.
  • MOTIF XS data (X0A, X0V, X0G, and X0W) can now be loaded to MONTAGE.
  • You can now switch Performances from the Live Set display during Audio playback.
  • Knob Brightness setting can now be stored.
  • Flags (tone generation attributes of Performance) can now be automatically set and displayed.
  • Arp Bypass and Kbd Ctrl Lock functions have been added for "Effect Switch."
  • Pedal fuctions such as sustain and sostenuto have been improved to reproduce realistic acoustic piano sound.

Fixed problems;

  • Fixed a problem in which all buttons, sliders, and knobs on the panel would not work after power-on.
  • Fixed a problem in which the Super knob would not work after power-on.
  • Fixed other minor problems.

V1.10 to V1.11

Fixed problems;

  • Improved the sensitivity of performance response.
  • Fixed a problem in which this instrument would freeze if you set Lane of the Motion Sequencer to "Arp" before starting MIDI recording.
  • Fixed a problem in which this instrument would freeze when reading certain Standard MIDI File data.

V1.02 to V1.10

New features;

  • New Performances have been added.
  • From the Performance Play (Home) display, you can now view Part types and categories of each Part.
  • From the Performance Play (Home) and the Mixing displays, you can now turn the Arpeggio Hold function on/off.
  • In the Part Category Search, you can now specify any Part other than Part 1 as the Part to be copied.
  • Performance Merge function has been added.
  • MIDI single channel mode has been added.
  • From the Data Utility display (in the Utility display) you can now delete multiple contents together.
  • You can now copy Performances from the Library memory to the User memory.
  • You can now copy or exchange Elements/Operators/Drum Keys.
  • You can now copy or exchange Live Sets on a Bank or page basis.
  • Live Set pages and slots can now be controlled by MIDI Bank Select and Program Change messages.
  • In the Live Set display, you can also register a Live Set by pressing the [SHIFT] and [LIVE SET] buttons simultaneously.
  • When you press the OCTAVE [+] or [-] button to change the octave or transpose setting, a pop-up display with the current value appears.
  • When you press the [SHIFT] and KNOB POSITION [1] or [2] buttons simultaneously to memorize the positions of knobs, a pop-up display appears.
  • "All" was added to the value of the display filter of the Control Assign display.
  • You can now change the cursor position in the text input with the right and left cursor buttons.

Fixed problems;

  • Fixed the problem in which a user waveform would be lost when loading libraries exceeding the sample memory size.
  • Fixed the problem of long load times when loading large samples.
  • Fixed the error in saving a Song as a MIDI file when the Song name contained illegal characters.
  • Fixed other minor problems.
  • This updater is only for the MONTAGE synthesizer.
  • This updater is to be used at the user's own risk.
  • All User memory (Library data, User data, User sample and so on) will be initialized by this updater. Please make sure that you have saved all User data to a USB flash drive before performing this update. To make backup file, connect USB device and go [UTILITY] > [Contents] > [Store / Save], set “Content Type” to “Backup File”, then Select the desired directory of the USB flash memory device and touch [Done].
  • The unit may become inoperable if the electrical supply is interrupted while running the updater (by disconnecting the AC cord, etc.). If this happens, run the updater again from the first step.
  • If the unit does not function after running the updater, please contact your nearest Yamaha service center.

Yamaha Global Gateway
https://www.yamaha.com/countries/

VEUILLEZ LIRE ATTENTIVEMENT CE CONTRAT DE LICENCE DE LOGICIEL (« CONTRAT ») AVANT D'UTILISER CE LOGICIEL. VOUS N'ÊTES AUTORISÉ À UTILISER CE LOGICIEL QUE CONFORMÉMENT AUX TERMES ET CONDITIONS DU PRÉSENT ACCORD. CET ACCORD EST CONCLU ENTRE VOUS (EN TANT QUE PERSONNE PHYSIQUE OU MORALE) ET YAMAHA CORPORATION (« YAMAHA »).

EN TELECHARGEANT, EN INSTALLANT, EN COPIANT OU EN UTILISANT DE TOUTE AUTRE MANIERE CE LOGICIEL, VOUS ACCEPTEZ D'ETRE LIE PAR LES TERMES DE CETTE LICENCE. SI VOUS N'ACCEPTEZ PAS LES CONDITIONS, NE TÉLÉCHARGEZ PAS, N'INSTALLEZ PAS, NE COPIEZ PAS ET N'UTILISEZ PAS CE LOGICIEL. SI VOUS AVEZ TÉLÉCHARGÉ OU INSTALLÉ LE LOGICIEL ET QUE VOUS N'ACCEPTEZ PAS LES CONDITIONS, CESSEZ RAPIDEMENT D'UTILISER LE LOGICIEL.

1. OCTROI DE LA LICENCE ET DES DROITS D'AUTEUR

Sous réserve des termes et conditions de cet Accord, Yamaha vous accorde par la présente une licence d'utilisation de copie(s) du/des programme(s) logiciel(s) et des données (« LOGICIEL ») accompagnant cet Accord, uniquement sur un ordinateur, un instrument de musique ou un élément d'équipement que vous possédez ou gérez vous-même. Le terme LOGICIEL englobe toutes les mises à jour du logiciel et des données qui l'accompagnent. Bien que vous soyez propriétaire du support de stockage dans lequel le LOGICIEL est stocké, le LOGICIEL lui-même est la propriété de Yamaha et/ou des concédants de licence de Yamaha, et est protégé par les lois sur les droits d'auteur en vigueur et toutes les dispositions des traités applicables. Bien que vous ayez le droit de revendiquer la propriété des données créées par l'utilisation du logiciel, ce dernier continuera à être protégé par les droits d'auteur pertinents.

2. RESTRICTIONS

  • Il est interdit de procéder à l'ingénierie inverse, au désassemblage, à la décompilation ou à toute autre forme de dérivation du code source du LOGICIEL par quelque méthode que ce soit.
  • Vous ne pouvez pas reproduire, modifier, changer, louer ou distribuer le LOGICIEL en tout ou en partie, ni créer des œuvres dérivées du LOGICIEL.
  • Vous ne pouvez pas transmettre électroniquement le LOGICIEL d'un ordinateur à un autre ou partager le LOGICIEL dans un réseau avec d'autres ordinateurs.
  • Vous ne pouvez pas utiliser le LOGICIEL pour distribuer des données illégales ou des données qui violent l'ordre public.
  • Vous ne pouvez pas lancer de services basés sur l'utilisation du LOGICIEL sans l'autorisation de Yamaha Corporation.
  • Vous ne pouvez pas utiliser le LOGICIEL d'une manière qui pourrait enfreindre les droits d'auteur de tiers ou les droits de propriété de tiers, à moins que vous n'ayez l'autorisation du propriétaire légitime du matériel ou que vous soyez légalement autorisé à l'utiliser.

Les données protégées par le droit d'auteur, y compris, mais sans s'y limiter, les données MIDI pour les chansons, obtenues au moyen du LOGICIEL, sont soumises aux restrictions suivantes que vous devez respecter.

  • Les données reçues au moyen du LOGICIEL ne peuvent être utilisées à des fins commerciales sans l'autorisation du détenteur des droits d'auteur.
  • Les données reçues au moyen du LOGICIEL ne peuvent être dupliquées, transférées ou distribuées, ni lues ou exécutées pour des auditeurs en public sans l'autorisation du détenteur des droits d'auteur.
  • Le cryptage des données reçues au moyen du LOGICIEL ne peut être supprimé et le filigrane électronique ne peut être modifié sans l'autorisation du détenteur des droits d'auteur.

3. TERMINATION

Le présent accord entre en vigueur le jour où vous recevez le LOGICIEL et reste en vigueur jusqu'à ce qu'il soit résilié. En cas de violation d'une loi sur le droit d'auteur ou d'une disposition du présent Accord, celui-ci sera automatiquement et immédiatement résilié sans préavis de la part de Yamaha. En cas de résiliation, vous devez immédiatement cesser d'utiliser le LOGICIEL et détruire tous les documents écrits qui l'accompagnent ainsi que toutes les copies de ces documents.

4. EXCLUSION DE GARANTIE SUR LES LOGICIELS

Si vous pensez que le processus de téléchargement était défectueux, vous pouvez contacter Yamaha, et Yamaha vous permettra de télécharger à nouveau le LOGICIEL, à condition que vous détruisiez d'abord toutes les copies ou copies partielles du LOGICIEL que vous avez obtenues lors de votre précédente tentative de téléchargement. Cette autorisation de retéléchargement ne limite en rien l'exclusion de garantie prévue à l'article 5 ci-dessous.
Vous reconnaissez et acceptez expressément que l'utilisation du LOGICIEL se fait à vos risques et périls. Le LOGICIEL et la documentation y afférente sont fournis « en l'état » et sans garantie d'aucune sorte. NONOBSTANT TOUTE AUTRE DISPOSITION DE CET ACCORD, YAMAHA REJETTE EXPRESSÉMENT TOUTES LES GARANTIES RELATIVES AU LOGICIEL, QU'ELLES SOIENT EXPRESSES OU IMPLICITES, Y COMPRIS, MAIS SANS S'Y LIMITER, LES GARANTIES IMPLICITES DE QUALITÉ MARCHANDE, D'ADÉQUATION À UN USAGE PARTICULIER ET DE NON-VIOLATION DES DROITS DES TIERS. EN PARTICULIER, MAIS SANS LIMITER CE QUI PRÉCÈDE, YAMAHA NE GARANTIT PAS QUE LE LOGICIEL RÉPONDRA À VOS EXIGENCES, QUE LE FONCTIONNEMENT DU LOGICIEL SERA ININTERROMPU OU SANS ERREUR, OU QUE LES DÉFAUTS DU LOGICIEL SERONT CORRIGÉS.

5. LIMITATION DE LA RESPONSABILITÉ

L'OBLIGATION ENTIÈRE DE YAMAHA EN VERTU DES PRÉSENTES SERA DE PERMETTRE L'UTILISATION DU LOGICIEL SELON LES TERMES DES PRÉSENTES. EN AUCUN CAS YAMAHA NE SERA RESPONSABLE ENVERS VOUS OU TOUTE AUTRE PERSONNE DE TOUT DOMMAGE, Y COMPRIS, SANS S'Y LIMITER, TOUT DOMMAGE DIRECT, INDIRECT, ACCESSOIRE OU CONSÉCUTIF, TOUTE DÉPENSE, TOUT MANQUE À GAGNER, TOUTE PERTE DE DONNÉES OU TOUT AUTRE DOMMAGE RÉSULTANT DE L'UTILISATION, DE LA MAUVAISE UTILISATION OU DE L'INCAPACITÉ À UTILISER LE LOGICIEL, MÊME SI YAMAHA OU UN REVENDEUR AGRÉÉ A ÉTÉ AVERTI DE LA POSSIBILITÉ DE TELS DOMMAGES. En aucun cas la responsabilité totale de Yamaha envers vous pour tous les dommages, pertes et causes d'action (qu'ils soient contractuels, délictuels ou autres) ne dépassera le montant payé pour le LOGICIEL.

6. LOGICIEL LIBRE

Ce LOGICIEL peut inclure le logiciel ou ses modifications qui incluent des licences open source, y compris, mais sans s'y limiter, la GNU General Public License ou la Lesser General Public License (« LOGICIEL OPEN SOURCE »). Votre utilisation des logiciels libres est soumise aux conditions de licence spécifiées par chaque détenteur de droits. En cas de conflit entre les termes et conditions du présent accord et chaque licence de source ouverte, les termes de la licence de source ouverte prévaudront uniquement en cas de conflit.

7. LOGICIELS ET SERVICES DE TIERS

Des logiciels, services et données de tiers (« LOGICIELS DE TIERS ») peuvent être attachés au LOGICIEL. SI, dans les documents écrits ou les données électroniques accompagnant le logiciel, Yamaha identifie tout logiciel et toute donnée en tant que LOGICIEL TIERS, vous reconnaissez et acceptez que vous devez respecter les conditions de tout accord fourni avec le LOGICIEL TIERS et que la partie fournissant le LOGICIEL TIERS est responsable de toute garantie ou responsabilité liée à ou découlant du LOGICIEL TIERS. Yamaha n'est en aucun cas responsable du LOGICIEL TIERS ou de l'utilisation que vous en faites.

  • Yamaha ne fournit aucune garantie expresse quant au LOGICIEL TIERS. EN OUTRE, YAMAHA DÉCLINE EXPRESSÉMENT TOUTE GARANTIE IMPLICITE, Y COMPRIS, MAIS SANS S'Y LIMITER, LES GARANTIES IMPLICITES DE QUALITÉ MARCHANDE ET D'ADÉQUATION À UN USAGE PARTICULIER, CONCERNANT LE LOGICIEL TIERS.
  • Yamaha ne vous fournira aucun service ou entretien concernant le LOGICIEL TIERS.

Yamaha n'est pas responsable envers vous ou toute autre personne de tout dommage, y compris, sans limitation, tout dommage direct, indirect, accessoire ou consécutif, dépenses, perte de profits, perte de données ou autres dommages résultant de l'utilisation, de la mauvaise utilisation ou de l'incapacité d'utiliser le LOGICIEL TIERS.

AVIS DE RESTRICTION DES DROITS DU GOUVERNEMENT DES ÉTATS-UNIS :
Le logiciel est un « article commercial », tel que ce terme est défini dans le 48 C.F.R. 2.101 (oct. 1995), consistant en un « logiciel informatique commercial » et une « documentation de logiciel informatique commercial », tels que ces termes sont utilisés dans le 48 C.F.R. 12.212 (sept. 1995). Conformément à 48 C.F.R. 12.212 et 48 C.F.R. 227.7202-1 à 227.72024 (juin 1995), tous les utilisateurs finaux du gouvernement des États-Unis doivent acquérir le logiciel avec les seuls droits énoncés dans le présent document.

8. GÉNÉRALITÉS

Le présent accord est interprété et régi par le droit japonais, sans référence aux principes de conflit de lois. Tout litige ou procédure est porté devant le tribunal de district de Tokyo au Japon. Si, pour quelque raison que ce soit, un tribunal compétent estime qu'une partie du présent accord est inapplicable, le reste de l'accord reste pleinement en vigueur. Tous les avis juridiques, les avis de litiges et les demandes d'arbitrage, ainsi que tout autre avis visant à modifier les présentes dispositions ou à faire valoir des droits légaux doivent être envoyés par écrit à l'adresse suivante :

Yamaha Corporation
10-1, Nakazawa-cho, Chuo-ku, Hamamatsu, Shizuoka, 430-8650, Japan

9. INTÉGRALITÉ DE L'ACCORD

Le présent accord constitue l'intégralité de l'accord entre les parties en ce qui concerne l'utilisation du LOGICIEL et de tous les documents écrits qui l'accompagnent et remplace tous les accords ou conventions antérieurs ou contemporains, écrits ou oraux, concernant l'objet du présent accord.

10. AMENDEMENT

Yamaha peut modifier, réviser ou mettre à jour cet Accord à sa discrétion. Toute modification ou mise à jour que Yamaha apporte à cet Accord sera effective après que vous ayez accepté les conditions mises à jour de cet Accord ou utilisé ce LOGICIEL.

Last updated : November 1, 2024