CL5 Firmware V5.90
Important Notices
Refer to these release notes when updating CL series. Please read the following instructions before updating.
Cautions when updating
- Use the "cl*_firm590.zip "(* is the model number) when updating.
- If updating from CL V5.80 or later, copy files "CL_SUBP_V590.BIN" and "MCLP5_90.PGM" to the root directory of the USB flash drive. Follow the instructions on the update guide. You don’t need to update the Dante firmware.
- If updating from CL V5.70 or older, copy files "CL_SUBP_V590.BIN" and "MCLP5_90.PGM" to the root directory of the USB flash drive. Follow the instructions on the update guide. You also need to update the Dante firmware. You can now update the Dante firmware for CL also by using the USB flash drive. This method allows you to update both the firmware and the "CL_SUBP_V590.BIN" and "MCLP5_90.PGM" files together at the same time.
- If updating from CL V1.61 or older, or if the message "NAME SUB CPU is old" appears after updating to V5. 90, copy "CL-MD101.BIN" file in CL*_firm590/NAME SUB (* is the model number) to the root directory of the USB flash drive. Follow the instructions on the update guide. This method allows you to update both the Dante firmware and the "CL_SUBP_V590.BIN" and "MCLP5_90.PGM" files together at the same time.
*IMPORTANT NOTES*
Before copying files, delete all files with extension .PGM and .BIN if any exists in the root directory of the USB memory. Prior to V3.0, the CL and QL Series used different files when updating, but both files used the same name * "C-MD1.BIN." For this reason, an error may occur during update when the incorrect "C-MD1.BIN" file is used or left in the root directory. Updating Dante firmware by using a USB flash drive takes approximately 30 minutes.
Please do not use the EEE function (*) of network switches in a Dante network.
Although power management should be negotiated automatically in switches that support EEE, some switches do not perform the negotiation properly. This may cause EEE to be enabled in Dante networks when it is not appropriate, resulting in poor synchronization performance and occasional dropouts.
Therefore, we strongly recommend that:
- If you use managed switches, ensure that they allow EEE to be disabled. Make sure that EEE is disabled on all ports used for real-time Dante traffic.
- If you use unmanaged switches, make sure to not use network switches that support EEE.
* EEE (Energy Efficient Ethernet) is a technology that reduces switch power consumption during periods of low network traffic. It is also known as Green Ethernet and IEEE802.3az.
Cautions for Dante Firmware
- You need to update the Dante-MY16-AUD firmware to V3.3.9 or later before using the Dante-MY16-AUD with the CL series.
- The Dante Firmware Update Manager since v1.4.16.6 for Windows does not support Windows XP. Please use Windows 7, Windows 8.1, or Windows 10.
- Follow the instructions on the update guide.
- The Dante settings might not be properly initialized when the firmware is updated, which results in data inconsistency between the CL/QL console and the R series units. This might occur only when the Dante Latency was set to 0.25ms or 0.5ms. Therefore, after updating, it is recommended to briefly change the Latency to 1.0ms on the console with the Console ID #1, then restore the original setting again. This will remove the possibility data inconsistency between the console and the mounted R series units. However, Dante Controller will be needed to manually change the settings of R series units that are not mounted on the console with Console ID #1.
Cautions for Dante Domain Manager (DDM)
- Please check here when using DDM.
CL/QL/RIVAGE PM/R/Tio Series Editor/Firmware/R Remote Compatibility
Please make sure to use appropriate version of CL Editor or QL Editor which is compatible with your console firmware in reference to the following compatibility chart. Using an unsupported Editor/firmware combination may result in unexpected behavior. The Firmware Set is a set of main (and sub) firmware of the device and the Dante firmware. The version of Firmware Set is the same as the version of the main firmware. Refer to the release note of each firmware about the details of the Firmware Set.
Main Revisions and Enhancements
New features in V5.90
- Added support for Rio3224-D3 & Rio1608-D3 device mounting and HA control.
- Added support for the latest Shure product variants and new RF Bands.
- Supports up to ULXD4 REV5, ULXD4D REV7, ULXD4Q REV7, QLXD4 REV4.
Changes in V5.90
- All outputs are now temporarily muted while loading a console file.
- Oscillator is now turned OFF when loading a console file, if the file was stored with the Oscillator ON.
Fixed bugs in V5.90
- Solved a problem in which With Recall On/Off for DM3 could not be set when mounted in the I/O Rack.
- Solved a problem in which the temporary disable status of mute override would be lost when recalling a scene if recall safe was set and mute was applied to each channel using DCA GROUP.
- Solved a problem when loading ALL data from a console file, in which the Recall Safe settings for Input, Mix, and Matrix were linked to the Channel Link settings before loading.
- Solved a problem in which “Brooklyn II” was displayed in the Dante Module item of ProVisionaire Edge, regardless of the actual Dante Module type.
- Solved a problem in which Individual Fade Time settings were not loaded when console files saved using V5.70 were loaded in V5.80.
- Solved a problem in which switching Daisy Chain/Redundant mode in Dante settings caused the mounted Dante devices to become uncontrollable when multiple models of Dante devices were mounted.
Known issues
- For hardware equipped with Brooklyn3, in rare cases, the Dante port may fail to LINK UP when the console is started. In this case, please turn on the power again.
- If a device running V5.80 or later has been enrolled in Dante Domain Manager and then is downgraded to V5.70 or earlier, the Dante module may occasionally not work correctly and control of the module is not possible. In the event of this happening, re-enroll the device in Dante Domain Manager and then restart it. Alternatively, initialize the device and its Dante settings* but make sure to back up the console data before initializing. * While holding down the [STORE] key and the [INC] key (CL series), or the master section A and B [SEL] keys (QL series), turn on the power to the device to initialize it.
- The following problems are found in version 8.1.1 of CL StageMix.
- If the CL StageMix screen is switched from the Master Bank that shows the Stereo/Mono levels properly to another bank and then returned to the Master Bank via the Navigation/Meter Bridge, the level meters in the Master Bank become inactive. This can be solved by rebooting the application or changing the metering points for Output Channels from the SETUP options.
- CL StageMix is often forced to terminate if a scene is recalled via a console just after the DANTE NAMES TO CHANNELS function in the Input Port Patch OPTIONS menu is executed. This can be solved by rebooting the application.
- The console may become inoperable after a "kernel sysdwn" message due to an unexpected error. If this happens, the console needs to be restarted. However, since all the settings including Dante settings* will be initialized to the default, please back up data regularly. * It will be set to DAISY CHAIN after the initialization. If the console is used via a redundant connection, unplug the Dante network cable first before reconfiguring the Dante settings.
- A device enrolled via DDM (Dante Domain Manager) rarely appears with a “VIRTUAL” indicator on the DEVICE MOUNT page. If this indicator is shown, press the REFRESH button.
- If Dante Virtual Soundcard (DVS) is patched to the CL series device using Dante Controller, the patching may not be recalled correctly when the CL series device is restarted. In such cases, patch the DVS again. In addition, when using a version of DVS for Windows that is older than v3.2.0, patches after CH41 cannot be performed from CL series consoles.
- Loading of a file created by version V1.15 or older will not include the mount information of Dante devices other than any connected R-series. It is the same when recalling a DANTE INPUT PATCH LIBRARY. Please reset MOUNT, PATCH, and DANTE INPUT PATCH Library data using V1.51 or later if necessary.
NOTICES
- You can use the following amount of CL/QL/RIVAGE PM/R Remote units to remotely control each device unit (listed at left).
- RMio64-D/RSio64-D/Tio1608-D (V1.04 or later): Maximum of four CL/QL units, or six R Remote units.
- Rio/Ri/Ro/Rio3224-D2/Rio1608-D2: Maximum of four CL/QL/RIVAGE PM units plus six separate computers operating R Remote.
- You can connect up to ten units of external controllers such as MonitorMix.
- When setting up the latency in Dante Controller, and there is a discrepancy in latency with the transmit device or the receive device, the largest (slowest) latency setting becomes effective.
- You need to assign Y###- (# is a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A - F (000 - FFF)) to the head of the device label for CL/QL consoles to recognize the device as a SUPPORTED DEVICE.
- An appropriate device label will be automatically assigned to a Dante-supported device manufactured by Yamaha by referring its device ID and so on. (You will still need to assign a device label manually to some of the products such as AIC128-D.)
- Device labels need to be assigned manually to third-party products including Dante-MY16-AUD2.
- Regarding wireless receivers manufactured by Shure, refer to their setup guide to set up properly.
- Restriction of a device label
- Y###-**********
- # is a three-digit hexadecimal number containing the digits 0 - 9 and uppercase A - F (000 - FFF)
- * indicates any desired character (alphabetical uppercase or lowercase, numerals, or - (hyphen) may be used) Up to 31 characters including the 'Y' are supported.
- For the R-series, make sure that the ID indicated by Y###- is not duplicated by any other R-series unit, even if it is a different size.
- In V2.0 and later, custom fader bank settings are not only included in user settings, but in scene data as well. The custom fader bank settings that are called up vary depending on the logged-in user, the type of the loaded data, and the version. Please note the following points:
- If you load console data of the ALL type as Administrator, the custom fader bank settings for the saved Administrator are recalled. If you load ALL data as Guest or another user, the custom fader bank settings for the saved current scene are called up.
- If you load ALL data that was saved in CL V1.70 or earlier, since scenes do not include custom fader bank settings, the custom fader bank settings for the current scene when the load was performed are applied to all scenes. Therefore, before loading ALL data, we recommend that you either change users to set the custom fader bank to the desired setting, or that you enable Recall Safe for the custom fader bank.
- File Converter V5.2.0, compatible with CL firmware V2.xx, V3.xx, V4.xx and V5.xx and QL firmware V3.xx, V4.xx and V5.xx has been made available for use.
Accord de licence et fichier de téléchargement
VEUILLEZ LIRE ATTENTIVEMENT CE CONTRAT DE LICENCE DE LOGICIEL (« CONTRAT ») AVANT D'UTILISER CE LOGICIEL. VOUS N'ÊTES AUTORISÉ À UTILISER CE LOGICIEL QUE CONFORMÉMENT AUX TERMES ET CONDITIONS DU PRÉSENT ACCORD. CET ACCORD EST CONCLU ENTRE VOUS (EN TANT QUE PERSONNE PHYSIQUE OU MORALE) ET YAMAHA CORPORATION (« YAMAHA »).
EN TELECHARGEANT, EN INSTALLANT, EN COPIANT OU EN UTILISANT DE TOUTE AUTRE MANIERE CE LOGICIEL, VOUS ACCEPTEZ D'ETRE LIE PAR LES TERMES DE CETTE LICENCE. SI VOUS N'ACCEPTEZ PAS LES CONDITIONS, NE TÉLÉCHARGEZ PAS, N'INSTALLEZ PAS, NE COPIEZ PAS ET N'UTILISEZ PAS CE LOGICIEL. SI VOUS AVEZ TÉLÉCHARGÉ OU INSTALLÉ LE LOGICIEL ET QUE VOUS N'ACCEPTEZ PAS LES CONDITIONS, CESSEZ RAPIDEMENT D'UTILISER LE LOGICIEL.
1. OCTROI DE LA LICENCE ET DES DROITS D'AUTEUR
Sous réserve des termes et conditions de cet Accord, Yamaha vous accorde par la présente une licence d'utilisation de copie(s) du/des programme(s) logiciel(s) et des données (« LOGICIEL ») accompagnant cet Accord, uniquement sur un ordinateur, un instrument de musique ou un élément d'équipement que vous possédez ou gérez vous-même. Le terme LOGICIEL englobe toutes les mises à jour du logiciel et des données qui l'accompagnent. Bien que vous soyez propriétaire du support de stockage dans lequel le LOGICIEL est stocké, le LOGICIEL lui-même est la propriété de Yamaha et/ou des concédants de licence de Yamaha, et est protégé par les lois sur les droits d'auteur en vigueur et toutes les dispositions des traités applicables. Bien que vous ayez le droit de revendiquer la propriété des données créées par l'utilisation du logiciel, ce dernier continuera à être protégé par les droits d'auteur pertinents.
2. RESTRICTIONS
- Il est interdit de procéder à l'ingénierie inverse, au désassemblage, à la décompilation ou à toute autre forme de dérivation du code source du LOGICIEL par quelque méthode que ce soit.
- Vous ne pouvez pas reproduire, modifier, changer, louer ou distribuer le LOGICIEL en tout ou en partie, ni créer des œuvres dérivées du LOGICIEL.
- Vous ne pouvez pas transmettre électroniquement le LOGICIEL d'un ordinateur à un autre ou partager le LOGICIEL dans un réseau avec d'autres ordinateurs.
- Vous ne pouvez pas utiliser le LOGICIEL pour distribuer des données illégales ou des données qui violent l'ordre public.
- Vous ne pouvez pas lancer de services basés sur l'utilisation du LOGICIEL sans l'autorisation de Yamaha Corporation.
- Vous ne pouvez pas utiliser le LOGICIEL d'une manière qui pourrait enfreindre les droits d'auteur de tiers ou les droits de propriété de tiers, à moins que vous n'ayez l'autorisation du propriétaire légitime du matériel ou que vous soyez légalement autorisé à l'utiliser.
Les données protégées par le droit d'auteur, y compris, mais sans s'y limiter, les données MIDI pour les chansons, obtenues au moyen du LOGICIEL, sont soumises aux restrictions suivantes que vous devez respecter.
- Les données reçues au moyen du LOGICIEL ne peuvent être utilisées à des fins commerciales sans l'autorisation du détenteur des droits d'auteur.
- Les données reçues au moyen du LOGICIEL ne peuvent être dupliquées, transférées ou distribuées, ni lues ou exécutées pour des auditeurs en public sans l'autorisation du détenteur des droits d'auteur.
- Le cryptage des données reçues au moyen du LOGICIEL ne peut être supprimé et le filigrane électronique ne peut être modifié sans l'autorisation du détenteur des droits d'auteur.
3. TERMINATION
Le présent accord entre en vigueur le jour où vous recevez le LOGICIEL et reste en vigueur jusqu'à ce qu'il soit résilié. En cas de violation d'une loi sur le droit d'auteur ou d'une disposition du présent Accord, celui-ci sera automatiquement et immédiatement résilié sans préavis de la part de Yamaha. En cas de résiliation, vous devez immédiatement cesser d'utiliser le LOGICIEL et détruire tous les documents écrits qui l'accompagnent ainsi que toutes les copies de ces documents.
4. EXCLUSION DE GARANTIE SUR LES LOGICIELS
Si vous pensez que le processus de téléchargement était défectueux, vous pouvez contacter Yamaha, et Yamaha vous permettra de télécharger à nouveau le LOGICIEL, à condition que vous détruisiez d'abord toutes les copies ou copies partielles du LOGICIEL que vous avez obtenues lors de votre précédente tentative de téléchargement. Cette autorisation de retéléchargement ne limite en rien l'exclusion de garantie prévue à l'article 5 ci-dessous.
Vous reconnaissez et acceptez expressément que l'utilisation du LOGICIEL se fait à vos risques et périls. Le LOGICIEL et la documentation y afférente sont fournis « en l'état » et sans garantie d'aucune sorte. NONOBSTANT TOUTE AUTRE DISPOSITION DE CET ACCORD, YAMAHA REJETTE EXPRESSÉMENT TOUTES LES GARANTIES RELATIVES AU LOGICIEL, QU'ELLES SOIENT EXPRESSES OU IMPLICITES, Y COMPRIS, MAIS SANS S'Y LIMITER, LES GARANTIES IMPLICITES DE QUALITÉ MARCHANDE, D'ADÉQUATION À UN USAGE PARTICULIER ET DE NON-VIOLATION DES DROITS DES TIERS. EN PARTICULIER, MAIS SANS LIMITER CE QUI PRÉCÈDE, YAMAHA NE GARANTIT PAS QUE LE LOGICIEL RÉPONDRA À VOS EXIGENCES, QUE LE FONCTIONNEMENT DU LOGICIEL SERA ININTERROMPU OU SANS ERREUR, OU QUE LES DÉFAUTS DU LOGICIEL SERONT CORRIGÉS.
5. LIMITATION DE LA RESPONSABILITÉ
L'OBLIGATION ENTIÈRE DE YAMAHA EN VERTU DES PRÉSENTES SERA DE PERMETTRE L'UTILISATION DU LOGICIEL SELON LES TERMES DES PRÉSENTES. EN AUCUN CAS YAMAHA NE SERA RESPONSABLE ENVERS VOUS OU TOUTE AUTRE PERSONNE DE TOUT DOMMAGE, Y COMPRIS, SANS S'Y LIMITER, TOUT DOMMAGE DIRECT, INDIRECT, ACCESSOIRE OU CONSÉCUTIF, TOUTE DÉPENSE, TOUT MANQUE À GAGNER, TOUTE PERTE DE DONNÉES OU TOUT AUTRE DOMMAGE RÉSULTANT DE L'UTILISATION, DE LA MAUVAISE UTILISATION OU DE L'INCAPACITÉ À UTILISER LE LOGICIEL, MÊME SI YAMAHA OU UN REVENDEUR AGRÉÉ A ÉTÉ AVERTI DE LA POSSIBILITÉ DE TELS DOMMAGES. En aucun cas la responsabilité totale de Yamaha envers vous pour tous les dommages, pertes et causes d'action (qu'ils soient contractuels, délictuels ou autres) ne dépassera le montant payé pour le LOGICIEL.
6. LOGICIEL LIBRE
Ce LOGICIEL peut inclure le logiciel ou ses modifications qui incluent des licences open source, y compris, mais sans s'y limiter, la GNU General Public License ou la Lesser General Public License (« LOGICIEL OPEN SOURCE »). Votre utilisation des logiciels libres est soumise aux conditions de licence spécifiées par chaque détenteur de droits. En cas de conflit entre les termes et conditions du présent accord et chaque licence de source ouverte, les termes de la licence de source ouverte prévaudront uniquement en cas de conflit.
7. LOGICIELS ET SERVICES DE TIERS
Des logiciels, services et données de tiers (« LOGICIELS DE TIERS ») peuvent être attachés au LOGICIEL. SI, dans les documents écrits ou les données électroniques accompagnant le logiciel, Yamaha identifie tout logiciel et toute donnée en tant que LOGICIEL TIERS, vous reconnaissez et acceptez que vous devez respecter les conditions de tout accord fourni avec le LOGICIEL TIERS et que la partie fournissant le LOGICIEL TIERS est responsable de toute garantie ou responsabilité liée à ou découlant du LOGICIEL TIERS. Yamaha n'est en aucun cas responsable du LOGICIEL TIERS ou de l'utilisation que vous en faites.
- Yamaha ne fournit aucune garantie expresse quant au LOGICIEL TIERS. EN OUTRE, YAMAHA DÉCLINE EXPRESSÉMENT TOUTE GARANTIE IMPLICITE, Y COMPRIS, MAIS SANS S'Y LIMITER, LES GARANTIES IMPLICITES DE QUALITÉ MARCHANDE ET D'ADÉQUATION À UN USAGE PARTICULIER, CONCERNANT LE LOGICIEL TIERS.
- Yamaha ne vous fournira aucun service ou entretien concernant le LOGICIEL TIERS.
Yamaha n'est pas responsable envers vous ou toute autre personne de tout dommage, y compris, sans limitation, tout dommage direct, indirect, accessoire ou consécutif, dépenses, perte de profits, perte de données ou autres dommages résultant de l'utilisation, de la mauvaise utilisation ou de l'incapacité d'utiliser le LOGICIEL TIERS.
AVIS DE RESTRICTION DES DROITS DU GOUVERNEMENT DES ÉTATS-UNIS :
Le logiciel est un « article commercial », tel que ce terme est défini dans le 48 C.F.R. 2.101 (oct. 1995), consistant en un « logiciel informatique commercial » et une « documentation de logiciel informatique commercial », tels que ces termes sont utilisés dans le 48 C.F.R. 12.212 (sept. 1995). Conformément à 48 C.F.R. 12.212 et 48 C.F.R. 227.7202-1 à 227.72024 (juin 1995), tous les utilisateurs finaux du gouvernement des États-Unis doivent acquérir le logiciel avec les seuls droits énoncés dans le présent document.
8. GÉNÉRALITÉS
Le présent accord est interprété et régi par le droit japonais, sans référence aux principes de conflit de lois. Tout litige ou procédure est porté devant le tribunal de district de Tokyo au Japon. Si, pour quelque raison que ce soit, un tribunal compétent estime qu'une partie du présent accord est inapplicable, le reste de l'accord reste pleinement en vigueur. Tous les avis juridiques, les avis de litiges et les demandes d'arbitrage, ainsi que tout autre avis visant à modifier les présentes dispositions ou à faire valoir des droits légaux doivent être envoyés par écrit à l'adresse suivante :
Yamaha Corporation
10-1, Nakazawa-cho, Chuo-ku, Hamamatsu, Shizuoka, 430-8650, Japan
9. INTÉGRALITÉ DE L'ACCORD
Le présent accord constitue l'intégralité de l'accord entre les parties en ce qui concerne l'utilisation du LOGICIEL et de tous les documents écrits qui l'accompagnent et remplace tous les accords ou conventions antérieurs ou contemporains, écrits ou oraux, concernant l'objet du présent accord.
10. AMENDEMENT
Yamaha peut modifier, réviser ou mettre à jour cet Accord à sa discrétion. Toute modification ou mise à jour que Yamaha apporte à cet Accord sera effective après que vous ayez accepté les conditions mises à jour de cet Accord ou utilisé ce LOGICIEL.
Last updated : November 1, 2024
Tu as aussi besoin
Manuels d'installation
Téléchargements associés
Versions précédentes
CL5 Firmware
- Previous versions information
- CL5 Firmware V5.85
- CL5 Firmware V5.81
- CL5 Firmware V5.80
- CL5 Firmware V5.70
- CL5 Firmware V5.60
- CL5 Firmware V5.51
- CL5 Firmware V5.50
- CL5 Firmware V5.10
- CL5 Firmware V5.01
- CL5 Firmware V5.00
- CL5 Firmware V4.51
- CL5 Firmware V4.50
- CL5 Firmware V4.10-2
- CL5 Firmware V4.04-2
- CL5 Firmware V4.02
- CL5 Firmware V4.01
- CL5 Firmware V4.00
- CL5 Firmware V3.11-2
- CL5 Firmware V3.10
- CL5 Firmware V3.02(from V1.70 and later)
- CL5 Firmware V3.02(from V1.61 and older)
- CL5 Firmware V2.04(from V1.70 and later)
- CL5 Firmware V2.04(from V1.61 and older)
- CL5 Firmware V2.03
- CL5 Firmware V1.70-2
- CL5 Firmware V1.61