Tio1608-D Rack E/S
| Tio1608-D | ||
|---|---|---|
| Sampling frequency rate | External | 44.1kHz or 48kHz |
| Signal delay | Less than 3ms INPUT to OUTPUT, connect with TF5 and NY64-D using Dante, Dante Receive Latency set to 0.25ms (one way), Fs=48kHz | |
| Total harmonic distortion | Less than 0.1% +4dBu@20Hz-20kHz into 600Ω, Gain=+66dB / Less than 0.05% +4dBU@20Hz-20kHz into 600Ω, Gain=-6dB, INPUT to OUTPUT, Fs=44.1kHz, 48kHz *Measured with a -18dB/octave filter @80kHz | |
| Frequency response | +0.5, -1.5dB 20Hz-20kHz, refer to the nominal output level @1kHz, INPUT to OUTPUT, Fs=44.1kHz or 48kHz | |
| Dynamic range | 108 dB, INPUT to OUTPUT, Gain=-6dB / 112 dB, DA Converter | |
| Hum & noise level | Equivalent input noise | -128dBu, Gain=+66dB *Measured with A-weighting filter |
| Residual output noise | -88dBu, ST master off *Measured with A-weighting filter | |
| Crosstalk | -100dB, adjacent INPUT/OUTPUT channels, Input Gain = -6dB *Measured with a -30dB/octave filter @22kHz | |
| Heat dissipation | 100-240V, 50/60Hz, 43.5kcal/h | |
| Power requirements | 100-240V, 50/60Hz | |
| Power consumption | 50W | |
| Dimensions | W | 480mm (18-7/8") |
| H | 88mm (3-4/8") | |
| D | 364mm (14-3/8") | |
| Net weight | 5.7kg (12.6lbs) | |
| Accessories | Owner’s Manual, Power Cord(2.5m), Rubber stoppers(4) | |
| Others | Temperature Range: Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃ | |
Analog input characteristics
| Input Terminals | GAIN | Actual Load Impedance |
For Use With Nominal | Input Level | Connector | Balanced / Unbalanced | ||
|---|---|---|---|---|---|---|---|---|
| Sensitivity*1 | Nominal | Max. before clip | ||||||
| INPUT1-16 | +66dB | 7.5kΩ | 50-600Ω Mics & 600Ω Lines |
-82dBu (61.6μV) | -62dBu (0.616mV) | -42dBu (6.16mV) |
Combo Jack (XLR-3-31 type *2 or TRS phone *3) |
Balanced |
| -6dB | -10dBu (245mV) | +10dBu (2.45V) | +30dBu (24.5V) | |||||
In these specifications, 0dBu = 0.775Vrms.
+48V DC (phantom power) can be supplied to INPUT XLR type connectors via each individual software controlled switch.
*1. Sensitivity is the lowest level that will produce an output of +4dBu (1.23V) or the nominal output level when the unit is set to maximum gain.
*2. 1: GND, 2: HOT, 3: COLD
*3. Tip: HOT, Ring: COLD, Sleeve: GND
Analog output characteristics
| Output Terminals | Actual Source Impedance |
For Use With Nominal |
Output Level | Connector | Balanced / Unbalanced | |
|---|---|---|---|---|---|---|
| Nominal | Max. before clip | |||||
| OUTPUT 1-8 | 75Ω | 600Ω Lines | +4dBu (1.23 V) | +24dBu (12.3V) |
XLR-3-32 type*1 | Balanced |
In these specifications, 0dBu = 0.775Vrms.
*1.1: GND,2: HOT, 3: COLD
Digital Input & Output Characteristics
| Terminal | Format | Data length | Level | Audio | Connector |
|---|---|---|---|---|---|
| Primary/Secondary | Dante | 24bit or 32bit | 1000Base-T | 16ch ( Tio1608-D to other devises) 8ch (Other devises to Tio1608-D) |
etherCON Cat5e |
